Powered by Blogger.

10 lệnh hữu ích cấu hình IP Interface

in this post, we are going to review how we can assign Static IP AddressStatic Route,Default Gateway etc.  Assigning IP Address on demand using IP command. IFCONFIG command is deprecated and replaced by IP command in Linux. However, IFCONFIGcommand is still works and available for most of the Linux distributions.

How do i Configure Static IP Address Internet Protocol (IPv4)

To configure static IP Address, you need to update or edit network configuration file to assign an Static IP Address to a system. You must be superuser with su (switch user) command from terminal or command prompt.

For RHEL/CentOS/Fedora

Open and edit network configuration file for (eth0 or eth1) using your favorite editor. For example, to assigning IP Address to eth0 interface as follows.
[root@tecmint ~]# vi /etc/sysconfig/network-scripts/ifcfg-eth0
Simple output:
DEVICE="eth0"
BOOTPROTO=static
ONBOOT=yes
TYPE="Ethernet"
IPADDR=192.168.50.2
NAME="System eth0"
HWADDR=00:0C:29:28:FD:4C
GATEWAY=192.168.50.1

For Ubuntu/Debian/Linux Mint

Assign Static IP Address to eth0 interface editing configuration file /etc/network/interfacesto make permanent changes as shown below.
auto eth0
iface eth0 inet static
address 192.168.50.2
netmask 255.255.255.0
gateway 192.168.50.1
Next, restart network services after entering all the details using the following command.
# /etc/init.d/networking restart
$ sudo /etc/init.d/networking restart

1. How to Assign a IP Address to Specific Interface

The following command used to assign IP Address to a specific interface (eth1) on the fly.
# ip addr add 192.168.50.5 dev eth1
$ sudo ip addr add 192.168.50.5 dev eth1
Note: Unfortunately all these settings will be lost after a system restart.

2. How to Check an IP Address

To get the depth information of your network interfaces like IP Address, MAC Address information, use the following command as shown below.
# ip addr show
$ sudo ip addr show
Sample Output
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
    link/ether 00:0c:29:28:fd:4c brd ff:ff:ff:ff:ff:ff
    inet 192.168.50.2/24 brd 192.168.50.255 scope global eth0
    inet6 fe80::20c:29ff:fe28:fd4c/64 scope link
       valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
    link/ether 00:0c:29:28:fd:56 brd ff:ff:ff:ff:ff:ff
    inet 192.168.50.5/24 scope global eth1
    inet6 fe80::20c:29ff:fe28:fd56/64 scope link
       valid_lft forever preferred_lft forever

3. How to Remove an IP Address

The following command will remove an assigned IP address from the given interface (eth1).
# ip addr del 192.168.50.5/24 dev eth1
$ sudo ip addr del 192.168.50.5/24 dev eth1

4. How to Enable Network Interface

The “up” flag with interface name (eth1) enables a network interface. For example, the following command will activates the eth1 network interface.
# ip link set eth1 up
$ sudo ip link set eth1 up

5. How to Disable Network Interface

The “down” flag with interface name (eth1) disables a network interface. For example, the following command will De-activates the eth1 network interface.
# ip link set eth1 down
$ sudo ip link set eth1 down

6. How do I Check Route Table?

Type the following command to check the routing table information of system.
# ip route show
$ sudo ip route show
Sample Output
10.10.20.0/24 via 192.168.50.100 dev eth0
192.168.160.0/24 dev eth1  proto kernel  scope link  src 192.168.160.130  metric 1
192.168.50.0/24 dev eth0  proto kernel  scope link  src 192.168.50.2
169.254.0.0/16 dev eth0  scope link  metric 1002
default via 192.168.50.1 dev eth0  proto static

7. How do I Add Static Route

Why you need to add Static routes or Manual routes, because that the traffic must not pass through the default gateway. We need to add Static routes to pass traffic from best way to reach the destination.
# ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0
$ sudo ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0

8. How to Remove Static Route

To remove assigned static route, simply type the following command.
# ip route del 10.10.20.0/24
$ sudo ip route del 10.10.20.0/24

9. How do I Add Persistence Static Routes

All the above route will be lost after a system restart. To add permanent Static route, edit file/etc/sysconfig/network-scripts/route-eth0 (We are storing static route for (eth0) and add the following lines and save and exist. By default route-eth0 file will not be there, need to be created.

For RHEL/CentOS/Fedora

# vi /etc/sysconfig/network-scripts/route-eth0
10.10.20.0/24 via 192.168.50.100 dev eth0

For Ubuntu/Debian/Linux Mint

Open the file /etc/network/interfaces and at the end add the persistence Static routes. IP Addresses may differ in your environment.
$ sudo vi /etc/network/interfaces
auto eth0
iface eth0 inet static
address 192.168.50.2
netmask 255.255.255.0
gateway 192.168.50.100
#########{Static Route}###########
up ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0
Next, restart network services after entering all the details using the following command.
# /etc/init.d/network restart
$ sudo /etc/init.d/network restart

10. How do I Add Default Gateway

Default gateway can be specified globally or for in interface-specific config file. Advantage of default gateway is If we have more than one NIC is present in the system. You can add default gateway on the fly as shown below command.
# ip route add default via 192.168.50.100
$ sudo ip route add default via 192.168.50.100
Kindly correct me if i missed out. Please refer manual page doing man ip from terminal/command prompt to know more about IP Command.
    Blogger Comment
    Facebook Comment